Among the most frustrating home renovating tasks is aiming to eliminate an old linoleum or vinyl floor. Even when the linoleum is pulled off, things just worsen. Now you’re confronted with gobs of old glue that seem harder than meteorites all over the floor.
Suggestions for ways to remove vinyl flooring, old linoleum or glue
Before getting depressed while reading this article, remember that there are a couple of methods around this formidable task.
One common alternative to removing old linoleum or vinyl floors is to put a new one right over it. If the existing floor is still smooth or can be smoothed with a few spots of FixAll, then the brand-new floor can be laid directly on top of the old.
In many cases, a layer of 1/4-inch plywood is laid over the old floor to provide a smooth base and after that the brand-new resilient floor is laid on that. In still another strategy, the old floor is floated with a self-leveling concrete that has to do with 1/8-inch thick when dry. The brand-new floor is placed on that.
When including a new floor, especially when adding plywood or self-leveling concrete, consider that this procedure is going to raise your floor significantly. The most essential concern is that it will not link smoothly with the nearby floors. This height difference might journey the unwary, specifically guests or the senior. Also, you will not have the same clearance under the toe kicks and you might have an issue in the future moving out your dishwasher, fridge, or range.
Eliminating old linoleum or vinyl is generally rather difficult due to the fact that wood, a common subfloor, is porous, therefore taking in the adhesives. One reason the old glues should be completely gotten rid of is due to the fact that some older adhesives had oils in them that chemically respond with new vinyl to cause a yellow staining. A lot of service warranties on new vinyl do not cover this kind of failure.
Another factor the old adhesives must be gotten rid of if you’re installing vinyl stripping is since they can ultimately end up being fragile. If old glue breaks loose under brand-new vinyl, it can cause failures in the new floor covering. Additionally, any bumps or cracks in an old floor will quickly appear as bumps or fractures in your brand-new linoleum.
Property owners also have to be aware that asbestos was used in some old linoleum and flooring adhesives, specifically in those made in the 1970s and earlier. Removing this product includes a health danger. If in doubt about your resilient flooring, break a small piece from a corner or behind the refrigerator and take it to an asbestos abatement firm for screening. Wetting the vinyl as you break it off and putting it in a baggie will keep any possible asbestos fibers from flying around. Asbestos reduction firms can be found in the Yellow Pages.
If asbestos is not present in your flooring, below are three methods you can remove it yourself, depending on the subfloor.
How to Remove Vinyl Floors | Watch video!
With a plywood subfloor, you have two choices: a) scrape away the linoleum or vinyl and glue or b) simply eliminated the subfloor and linoleum or vinyl flooring as one piece.
To get rid of old resilient flooring, first cut it into parallel strips about 6 inches large with an energy knife. Utilize a hammer to tap a stiff putty knife or brick chisel under the linoleum to break it loose. Pull the linoleum up in strips to expose the support or the glue. Once the surface layer is gone, utilize a paint scraper to get rid of the glue. You can likewise make use of a heat weapon to soften the glue as you scrape it away with the paint scraper. Some old linoleum has tar-based adhesive, which can be softened by applying mineral spirits.
To get rid of the linoleum and subfloor together, drill a hole through the floor to figure out how thick the plywood is. Set the saw blade to cut simply 1/8 inch deeper and remove an area of flooring on one side of the space. To cut flush versus the walls, make use of a mutual saw, but take care you do not cut the floor joists. Cut the floor into workable areas about 3 or 4 feet long as you remain to remove it. When setting the new subfloor, nail crosspieces between the joists to support adjacent plywood subfloor edges, specifically if the old floor was tongue and groove plywood.
It’s not unusual to find a perfectly great (or exactly what used to be) hardwood floor under linoleum or vinyl. Peel away enough covering in a corner till you can judge which way the flooring runs. Cut through the vinyl in about 6-inch-wide strips in the same direction the floor goes to decrease any possibilities of cutting across the grain. Set the energy knife blade just deep enough to obtain through the linoleum or vinyl. Heat the linoleum with a heat weapon and after that pry it and the glue up while the glue is still soft. Scrape away as much of the glue as you can while bewaring not to gouge the floor. When you have cleaned the floor as well as possible, sand away any remaining glue and refinish the floor.
If you are having problem choosing between hardwood and carpeting flooring, see how they compare.
This is probably the easiest kind of subfloor to obtain linoleum or vinyl off of, however it’s still no picnic. Once again, it’s the very same procedure of cutting the flooring into strips, heating it with a heat gun to soften it, and then pulling it off. The remaining glue can be scraped with a floor scraper or drenched over night with water and dish soap, which assists soften the glue.
As you battle with your old flooring, simply keep thinking great thoughts and advising yourself that you and your house will both be better for it when you’re completed.